Food Safety Tech Test

Cleaning and facilities

This area covers the building and what keeps it clean: floors and equipment, plumbing, handwashing stations, garbage, cleaning and sanitizing, dishwashing, chemicals and pests.

A kitchen that cannot be cleaned will not stay safe, however careful the staff are. The topics here run from how the room is built to what happens at the dish sink at closing.

Floors, walls and equipment standards

Floors, walls and ceilings in food areas must be smooth, durable, nonabsorbent and easy to clean. Sealed quarry tile meets the standard. Unsealed wood or concrete soaks up liquid and fails it. Coving, a curved and sealed edge where the floor meets the wall, closes the corner where dirt and moisture collect.

Equipment that is too heavy to move needs space underneath for cleaning, or no space at all:

Equipment Minimum installation
Floor-mounted, such as a fryer Legs at least 6 inches high, or sealed to the floor on a masonry base
Tabletop, such as a heavy slicer Legs at least 4 inches high, or sealed to the countertop

Food-contact surfaces must be smooth, nonabsorbent, corrosion-resistant and safe, which is why prep tables are stainless steel. A cutting board with deep grooves or a crack is resurfaced or replaced, because sanitizer cannot reach what sits in the grooves. When buying equipment, look for the mark of an accredited sanitation certification program. Broken floor tiles and flaking ceiling tiles are repaired promptly.

The exam mistake is swapping the two numbers. Six inches belongs to the floor, 4 inches to the counter.

Water and plumbing: cross-connections and backflow

Only drinkable (potable) water from an approved source may be used. A private well qualifies if it is tested regularly and meets the standards of the regulatory authority.

A cross-connection is a physical link through which dirty water can reach the drinkable supply. Backflow is the reverse flow through that link. Backsiphonage is backflow caused by a pressure drop, for example when firefighters open hydrants on the street. A hose left lying in a mop bucket is the classic cross-connection.

The most reliable protection is an air gap: open space between the water outlet and the flood rim of the sink. The Food Code sets it at twice the diameter of the water inlet and never less than 1 inch. Vacuum breakers and other mechanical devices also prevent backflow, but they can fail, so a licensed plumber checks them on a schedule.

A grease trap needs regular cleaning, or wastewater backs up. A sewage backup or the loss of drinkable water is an imminent health hazard: service stops and the regulatory authority is notified, as covered under emergencies and imminent health hazards.

On the exam, people pick the vacuum breaker as the most reliable method. The answer is the air gap.

Handwashing stations, lighting, ventilation and garbage

Handwashing stations are required in or next to restrooms and in the areas for food prep, service and dishwashing. Each one needs five things:

  • Hot and cold running water
  • Soap
  • A way to dry hands, such as single-use paper towels or a hand dryer
  • A garbage container
  • A sign that tells staff to wash their hands

A handwashing sink is used for handwashing only and must stay reachable. Rinsing strawberries in it or parking sheet pans in front of it are both violations. The steps of washing itself are in personal hygiene.

Lights over exposed food, clean equipment and utensils must be shielded or shatter-resistant, so a broken bulb cannot drop glass into food. Ventilation must remove grease and steam. Grease dripping from the hood or a sticky film on the walls means the system needs cleaning or repair.

Garbage leaves prep areas as quickly as possible. Containers are cleaned away from food areas. Outdoor containers sit on concrete or asphalt with tight lids kept closed.

The common wrong answer accepts hand antiseptic or gloves as a fix for a blocked or unstocked sink.

What is the difference between cleaning and sanitizing?

Cleaning removes food and dirt from a surface. Sanitizing reduces the pathogens on that clean surface to safe levels. Sanitizer does not work through crumbs and grease, so a surface is always handled in this order:

  1. Clean with detergent.
  2. Rinse with clean water.
  3. Sanitize.
  4. Air-dry.

Food-contact surfaces are cleaned and sanitized after use, before work with a different type of food, after any interruption in which they may have been contaminated, and at least every 4 hours when in constant use with TCS food. A slicer that starts on roast turkey at 8 a.m. is due by 12 noon. A board used for raw chicken is washed, rinsed and sanitized before the romaine goes on it.

Sanitizing is done with heat or with chemicals. For heat in a sink, items soak in water of at least 171°F for at least 30 seconds. For chemicals, mix to the concentration on the manufacturer’s label and check it with a test kit. Five factors decide whether the solution works: concentration, water temperature, contact time, water hardness and pH. A weak solution may not sanitize. A solution mixed at three times the label strength can be toxic and corrode equipment. Replace the solution when it is dirty or tests low.

The classic mistakes are drying a sanitized counter with a towel and rinsing after the sanitizer. Both remove the sanitizer before its contact time is up.

Dishwashing machines and the three-compartment sink

Before the first pot goes in, the sinks and drainboards themselves are cleaned and sanitized. Then five steps follow:

  1. Scrape or rinse the items.
  2. Wash in the first sink with detergent and water.
  3. Rinse in the second sink with clean water.
  4. Sanitize in the third sink.
  5. Air-dry, upside down so water drains.

Skipping the rinse carries detergent into the sanitizer and weakens it. Wash water is changed when it is greasy or the suds are gone.

Machines sanitize with hot water or with chemicals:

Method Minimum temperature
High-temperature machine, final sanitizing rinse 180°F
Stationary-rack, single-temperature machine, final sanitizing rinse 165°F
Hot water immersion in a sink 171°F for at least 30 seconds

Items are scraped before loading, and racks are never overloaded. If a chemical-sanitizing machine runs out of sanitizer, everything washed since then goes through again.

Store clean glasses upside down and flatware with handles up, at least 6 inches off the floor. The same height applies to food in storage.

The exam likes to offer 171°F for the machine and 180°F for the sink. It is the other way around.

Cleaning program, wiping cloths and chemical storage

A master cleaning schedule states what is cleaned, who cleans it, when and how.

Item Rule
Wet wiping cloths Kept in sanitizer solution between uses
Cloths used around raw meat, fish or poultry Kept separate from all other cloths
Mop water Emptied into a service sink or floor drain, never a prep or handwashing sink
Mops and brushes Cleaned at the service sink and hung on hooks to air-dry
Working containers, such as spray bottles Labeled with the common name of the chemical
Chemicals Stored away from food, utensils and equipment, and never above them
Safety data sheets Kept where all staff can reach them during work

The operation must have written procedures for cleaning up vomit and diarrhea, and staff must be trained in them. Vomit can carry Norovirus, so uncovered food near the spot is thrown away. A pan of cut fruit 3 feet from where a child vomited is discarded.

The tempting wrong answer is a cloth tucked into an apron or left on the counter between uses.

Pest prevention and control

Integrated pest management has three rules: keep pests out, deny them food, water and shelter, and work with a licensed pest control operator to remove those that get in.

  • Check deliveries before they enter the building and refuse any with pests or egg cases.
  • Keep outside doors closed, or fit screens or air curtains.
  • Seal gaps around pipes with concrete or sheet metal.
  • Clean up spills at once and remove empty cardboard.
Pest Signs
Cockroaches Strong oily odor, droppings like grains of black pepper, capsule-shaped egg cases
Rodents Gnaw marks, dark pellet-shaped droppings, nests of shredded paper or cloth

A single cockroach seen in daylight can point to a large hidden infestation, so the manager calls the operator promptly. Only the licensed operator applies pesticides. Pesticides kept on site stay in their original containers in a secure place away from food. After a treatment, food-contact surfaces are washed, rinsed and sanitized before prep starts.

The usual wrong answer has the owner spraying the kitchen with a store-bought product after closing.

What to remember

  • Floor equipment: 6-inch legs or sealed to the floor. Tabletop equipment: 4-inch legs or sealed to the counter.
  • An air gap is the most reliable backflow prevention.
  • A handwashing sink is for handwashing only and needs water, soap, hand drying, a garbage container and a sign.
  • Surfaces: clean, rinse, sanitize, air-dry. Never towel-dry.
  • Three-compartment sink: scrape or rinse, wash, rinse, sanitize, air-dry.
  • Hot water sanitizing: 171°F for 30 seconds in a sink, 180°F final rinse in a high-temperature machine, 165°F in a stationary-rack, single-temperature machine.
  • Food-contact surfaces in constant use with TCS food are cleaned and sanitized at least every 4 hours.
  • Pesticides are applied by a licensed pest control operator only.

Test this area with the cleaning and facilities quiz, or mix all topics in practice test 1.

Common questions

What is the difference between cleaning and sanitizing?

Cleaning removes food and dirt from a surface. Sanitizing reduces the pathogens on the clean surface to safe levels. Cleaning always comes first, and the order is clean, rinse, sanitize, air-dry.

What are the 5 steps for a three-compartment sink?

Scrape or rinse the items, wash them in the first sink, rinse them in the second, sanitize them in the third, and let them air-dry. The sinks and drainboards are cleaned and sanitized before the first item goes in.

How hot does the water have to be to sanitize dishes?

Hot water in a sink must be at least 171°F and items soak for at least 30 seconds. The final sanitizing rinse of a high-temperature dish machine must reach 180°F, or 165°F in a stationary-rack, single-temperature machine.

How often must food-contact surfaces be cleaned and sanitized?

After each use, before working with a different type of food, after any interruption in which they may have been contaminated, and at least every 4 hours when in constant use with TCS food.

How high off the floor must kitchen equipment be?

Floor-mounted equipment that cannot be moved easily stands on legs at least 6 inches high or is sealed to the floor. Tabletop equipment stands on legs at least 4 inches high or is sealed to the counter.

Last checked against ServSafe information and the FDA Food Code in November 2026.

All practice tests